A. Dual-rank DIMMs are not supported.
B. 16-GB DIMMs are too slow.
C. The largest DIMM an Intel 55xx or 56xx CPU can address is 32 GB
D. The memory bus would be too long.
E. The blade would run too hot.
您可能感興趣的試卷
你可能感興趣的試題
A. Missing control VLAN in VSM configuration
B. Missing packet VLAN in VSM configuration
C. VSM has no network connection to vCenter
D. VSM extension key is not installed on vCenter
E. vCenter extension key is not installed on VSM
The network administrator is adding a new N1Kv to the vCenter， however， the administrator does not see the new switch under the networking tab of vCenter.
The administrator issues the following command on the VSM to troubleshoot：
VSM# show svs connections
connection VC：
ip address： 10.10.10.30
remote port： 80
protocol： vmware-vim https
certificatE. default
datacenter namE. DC1
DVS uuiD. 67 32 30 50 a6 d2 49 64-9e 1c 5f 49 e3 af 55 99
config status： Disabled
operational status： Disconnected sync status： -
version： -
When attempting to fix the issue， the following error is seen：
VSM-PRI-188# conf
VSM-PRI-188（config）# svs connection VC
VSM-PRI-188（config-svs-conn）# connect
ERROR： [VMWARE-VIM] Extension key was not registered before its use
What is the cause of the error？（）
A. Missing control VLAN in VSM configuration
B. Missing packet VLAN in VSM configuration
C. VSM has no network connection to vCenter
D. VSM extension key is not installed on vCenter
E. vCenter extension key is not installed on VSM
Given the following configuration：
port-profile type ethernet DATA-UPLINK
vmware port-group
switchport trunk allowed vlan 1-3967，4048-4093
channel-group auto mode on
no shutdown
state enabled
port-profile type ethernet MGMT-UPLINK
vmware port-group
switchport trunk allowed vlan 10-12
channel-group auto mode on
no shutdown
state enabled
VEMs are seen to be joining and then are lost from the Cisco VSM. How would you resolve this issue？（）
A. Remove second NIC from each port profile
B. Remove VEM from VSM （no vem X）， remove NICs， and reinsert
C. Ensure that VLANs on uplink profiles are not overlapping
D. Reinstall VEM
E. Issue the command "module vem X execute vemcmd set pinning module vsm 1"
A. Send monitored traffic to a VLAN
B. Send monitored traffic to a remote VEM over L2
C. Receive monitored traffic on a vEthernet interface
D. Send monitored traffic to an IP destination
A. Source and destination interface must be on the same host
B. Source and destination interfaces can be on different hosts
C. Destination vEthernet interface can be on a different VLAN than the source
D. Destination interface can be a physical port
E. Destination interface cannot be a physical port
最新試題
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）
Which statement is true regarding Backup tasks in Cisco UCS？（）
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）
What is the appliance port used to connect to in a Cisco Unified Computing System？（）
In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）
Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）. Which actions might be used to change this behavior？（）
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）
What is the use of an "all configuration" backup in Cisco UCS？（）
Which of the following are supported in Cisco Global Site Selector？ （）