A.ip sla 1 icmp-echo 1.1.1.1 tos 12
B.ip sla 1 icmp-echo 1.1.1.1 tos 96
C.ip sla 1 icmp-echo 1.1.1.1 precedence 3
D.ip sla 1 icmp-echo 1.1.1.1 dscp 12
您可能感興趣的試卷
你可能感興趣的試題
A.ip sla monitor low-memory
B.ip sla group schedule
C.ip sla reaction-trigger
D.ip sla enable timestamp
Refer to the exhibit. In this network， R1 is configured not to perform autosummarization within EIGRP. What routes will R3 learn from R2 through EIGRP？ （）
A. 172.30.1.0/24 and 10.1.2.0/24；EIGRP only performs autosummarization at the edge between two major networks.
B. 172.30.0.0/16 and 10.1.2.0/24；R2 will perform autosummarization although R1 will not.
C. Since R2 is configured without autosummarization， it will not propagate the 172.30.1.0/24 route.
D. 172.30.0.0/8 and 10.0.0.0/8.
Refer to the exhibit. In this network， R1 has been configured to advertise a summary route， 192.168.0.0/22， to R2. R2 has been configured to advertise a summary route， 192.168.0.0/21， to R1. Both routers have been configured to remove the discard route （the route to null created when a summary route is configured） by setting the administrative distance of the discard route to 255. What will happen if R1 receives a packet destined to 192.168.3.1？（）
A. The packet will loop between R1 and R2.
B. It is not possible to set the administrative distance on a summary to 255.
C. The packet will be forwarded to R2， where it will be routed to null0.
D. The packet will be dropped by R1， since there is no route to 192.168.3.1.
A.Upgrade the switches
B.Configure BPDU guard
C.Configure VLAN access lists
D.Configure port security
E.Configure Dynamic ARP inspection
A. Attempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall. If telnet works， BGP will work， since telnet and BGP both use TCP to transport data.
B. Ping from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall. If you can ping between them， BGP should work， since BGP uses IP to transport packets.
C. There is no way to make BGP work across a firewall without special configuration， so there is no simple test that will show you if BGP will work or not， other than trying to start the peering session.
D. There is no way to make BGP work across a firewall.
最新試題
Which three message types are valid PIMv2 message types？（）
All of these are fundamental building blocks of differentiated services Traffic Conditioner Block exceptwhich one？（）
Which of the following is true about the MPLS header and its EXP field size？（）
What is the command to configure RSVP to reserve up to one-tenth of a Gigabit link，but only allow eachindividual flow to use 1 MB/s？（）
Which message type is constructed and sent from an MSDP router to its MSDP peers when it receives a PIM register message knowing that the MSDP router is also configured as an RP for the PIM domain？（）
What is also called Type 0 authentication in OSPF on Cisco Routers？（）
Based on the output provided in the exhibit， to which address or location will the router forward a packet sent to 192.168.32.1？（）
Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree ProtocolIEEE 802.1 D？（）
What is the correct command to set the router ID for an OSPFv3 process？（）
The classic Spanning Tree Protocol （802.1 D 1998） uses which sequence of variables to determine thebest received BPDU？（）